『模具工程』

标题	作者	回复/查看	最后发表
共享】欧美模具标准！希望对大家有用！	kuju 2006-10-14	2 / 296	2008-6-12 14:25 by jerryandtom
公差原则	jchuan 2008-2-12	5 / 236	2008-6-12 14:20 by jerryandtom
cad 入门	holywchsh 2008-6-7	1 / 56	2008-6-12 13:58 by jerryandtom
注射模具的水路有何要求？？？	jerryandtom 2008-6-12	0 / 69	2008-6-12 13:55 by jerryandtom
模具技术 1 2 3	tianyazhixin 2008-4-1	30 / 1139	2008-6-12 13:48 by jerryandtom
模具设计指南 1 2 3	ox521 2006-9-13	32 / 1179	2008-6-12 09:58 by shibai1000
镗转向节衬套孔的夹具设计图	yishin606 2007-7-15	1 / 298	2008-6-11 22:10 by wuzhao1985
设计成品图-  镗转向节衬套空的夹具	yishin606 2007-7-16	1 / 283	2008-6-11 22:09 by wuzhao1985
CA1092汽车转向节零件图及镗转向节衬套孔夹具的设计资料	yishin606 2007-7-15	2 / 1138	2008-6-11 22:08 by wuzhao1985
超全注射模具资料	dada1670 2008-6-10	4 / 61	2008-6-10 22:44 by dada1670
cad新手入门	holywchsh 2008-6-7	0 / 26	2008-6-7 12:37 by holywchsh
咖啡壶手柄气辅注射成型模具设计	kuju 2006-10-14	1 / 283	2008-6-7 09:27 by hc111111
冲压文集	kuju 2006-10-1	8 / 1124	2008-6-6 07:05 by wei520820
基于ＤＹＮＡＦＯＲＭ的汽车覆盖件模具型面设计及成形性分析	wusowee 2008-1-17	1 / 187	2008-6-6 07:04 by wei520820
求助CQZ6954汽车车架焊装夹具设计 ~~急！	zflovejing 2008-6-4	0 / 34	2008-6-4 17:03 by zflovejing
车门内板二次拉延修边冲孔模	fly6231 2008-1-1	4 / 265	2008-6-2 20:59 by ivnbwwkvco
机械设计手册软件版R2.0破解文件	kuju 2006-10-14	2 / 450	2008-5-31 21:04 by deanmxh
油缸标准	tianyazhixin 2008-4-1	2 / 247	2008-5-31 17:10 by huanlan518
玻璃纤维	tianyazhixin 2008-4-1	3 / 157	2008-5-30 07:18 by fmingxi
三米长的连续模	cjczq 2008-5-28	3 / 90	2008-5-30 07:14 by fmingxi

1716 1 ...‹‹5 678 9 10 11 12 13 14 ››... 86

有新回复

无新回复

热门主题

关闭主题